Larson Electronics 15KVA Temporary Power Distribution - 208V to 208Y/120V 3PH - (8) 5-15R Duplex GFCI Receptacles

Made in Texas The Larson Electronics MGL-208D-15KVA-208Y.120-8X120.1P.15A temporary power distribution system converts three phase 208V electrical current into three phase 208Y/120VAC. This unit provides operators the ability to safely tap into and distribute 208VAC power from a variety of sources including generators and direct grid power. *PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO POWER DISTRIBUTION PANELS, TRANSFORMERS, OR SUBSTATIONS* Portable Power Distribution Purpose and Use: The MGL-208D-15KVA-208Y.120-8X120.1P.15A portable power distribution system gives operators the ability to power their 120V equipment from a single system. On the primary side, operators connect 208 volt using a 25` #8 Type W cord with a 460P9W 250V cord cap. On the secondary side, operators connect to eight 5-15R receptacles for 120V equipment. Operation: A 25` #8 Type W cord with a 460P9W 250V cord cap brings three phase 208V power to the NEMA 3R 60-amp 208V three phase primary disconnect, which contains three 50-amp time delay fuses and passes 208V three phase through to the transformer. The NEMA 3R 15KVA transformer converts 208V three phase power to 208Y/120V three phase and passes the current to the secondary side. The secondary side of the transformer feeds a NEMA 3R 100-amp 208Y/120V three phase main lug only panel. This secondary side contains eight 15-amp breakers, protecting eight 15-amp 125V duplex GFCI receptacles. Protective Construction: The transformer and load center/distribution assembly is mounted to a powder coated steel, dolly cart style frame resulting in an extremely stable, durable, and mobile power distribution platform. Two run-flat rubber tires and a dolly cart style mounting platform provides easier substation mobility, and a center point lift point allows easy lifting with cable or chain hooks. This temporary power distribution solution can be modified to meet the needs of job-site receptacle requirements. Units are available up to 150KVA and can be equipped with skids or trailer mounted. Certification: Larson Electronics is a UL 1640 panel shop and certified to build portable power distribution systems. All units are built in accordance to NFPA 70 (National Electric Code) and certified to UL 1640. All equipment is NEMA 3R rated for indoor and outdoor use and provide a degree of protection against dirt, water, and ice. NEMA 4 and NEMA 4X equipment can be equipped upon request. Grounding: Transformer is grounded to the frame and we provide a grounding lug on the frame for the earth ground. ~Please check all motor loads for dual rated motors that will work 208 or 240.~ Applications: This power distribution system is NEMA 3R rated and ideal for indoor/outdoor use and applications including but not limited to; construction sites, plant maintenance, plant turnarounds, shows, exhibits and shipyard operations. Larson Electronics is a manufacturer and as such can build portable transformer systems to your specifications. Although we carry several models of power distribution transformers, we can deliver custom ordered units almost as quickly as our prebuilt units. If this model does not meet your needs, please contact us at 888-325-4448 [email protected] to discuss your specific requirements. Specifications / Additional Information MGL-208D-15KVA-208Y.120-8X120.1P.15A -Temporary Power Distribution System Ratings Line In: 25’ #8 3c4w Type W Cord UL 1640 Portable Power-Distribution Equipment Cord Cap: 460P9W 60A 3Ph [250V] NEMA 3R Indoor or Outdoor Use Primary Voltage: 208VAC 3PH Made in the USA Disconnect: 250V 3Ph 60A Fused @ 50A N3R Protection: Time Delay Fuses Transformer: 15KVA 60Hz 208V to 208Y/120V 3PH N3R Secondary Voltage: 208Y/120VAC 3Ph Secondary Panel: 208Y/120V 3PH 100A MLO N3R Panel Secondary Breakers: (8) 15A 1P 125V Secondary Outlets: (8) 5-15R 15A Duplex GFCI [125V] Secondary Protection: Circuit Breakers, GFCI`s Form Factor: Powder Coated Steel Dolly Cart w/ Run Flat Tires Dimensions: W-40" X D-40" X H-48" Special Orders- Requirements Weight: 350 lbs Contact us for special requirements Features: Toll Free: 888-325-4448 Primary Max OCP: 50 amps @ 208V Secondary Max Output: 41.6 amps @ 208V E-mail: [email protected] Larson Electronics manufacture a wide variety of custom power distribution systems. The pictures displayed for this unit are a general representation of form factor and may not accurately represent this exact configuration in every detail due to being custom builds. The specifics for this configuration are listed in the specification table and one-line diagram. *All grounding shall comply with state and local codes and meet the minimum requirements of the National Electronic Code section 250* Scroll Down to Purchase