Exit Signs:
Exit signs save lives in case of fire or disaster. If your building loses power, exit signs with battery backup can guide people to safety. We sell a variety of exit signs to comply with building fire & insurance codes. If you are looking for a heavy duty wet location exit sign for outdoor placement or just looking to save some money with an energy efficient LED exit sign, we have it for you.
4.8 Volt:
Federally approved high temperature 4.8 Volt exit sign and emergency lighting NiCd batteries. A 4.8 Volt NiCd has four AA, AAA, C, Sub-C, D or F cells in a battery pack that can come in a variety of configurations. Most common are cube, row and stick configurations.
Nickel-Cadmium:
The nickel-cadmium battery is a type of rechargeable battery using nickel oxide hydroxide and metallic cadmium as electrodes. The abbreviation NiCd is derived from the chemical symbols of nickel and cadmium. NiCd batteries have a longer shelf life of around 10 years. The NiCd batteries sold on this site are High Temperature NiCds batteries with outstanding charge/discharge characteristics at both room temperature and high temperature up to 70Deg. C (158Deg. F).
LED Lighting:
Visibility, brightness and long life are very important factors that should be thought about when purchasing and exit sign. Light emitting diode or LED exit signs & emergency lights have proven to be successful in the reducing electricity consumption by up to 85%. LED exit signs can save money and power while still emitting considerable amounts of light.
Ceiling Mount:
These products can be hung from the ceiling. Many exit signs come with the ceiling mounting canopy included.
Surface/ WallMount:
Exit signs & emergency lights that are surface mountable are typically one sided and have a back plate that can be connected directly to a wall or flat surface.
Title 20:
Title 20 is part of the CEC's Appliance Efficiency Regulation and California Code of Regulations that requires manufacturer certification of "self-contained" lighting control devices in California.
"Self-contained" lighting control devices are defined as discrete lighting control devices that can perform their designed function without the requirement of being connected to additional devices.
Common devices that may fall under the category of "Self-contained" include:
- Self-contained Automatic Daylighting Controls
- Dimmers
- Line powered Occupancy Sensors
- Line power Vacancy Sensors
Damp Location:
A damp location is an interior location normally subject to dampness or condensation, or an exterior location protected from weather and not subject to saturation with water. Damp locations include over bathtubs, indoor pools, covered porches, and like locations.
Remote Capable:
Remote capable exit signs or emergency lights allow the unit to add additional lighting with remote light heads without adding additional fixtures.
Aluminum:
Brushed die-cast aluminum housings provide a modern appearance with ultimate functionality.
AC Only:
AC only exit signs do not include a battery backup or charging circuitry and are for installation and use only where emergency power is supplied from a remote or secondary AC power supply.
Dual Circuit:
Dual circuit exit signs. These unit allows the fixture to have dual power feeds. The idea behind this is so that when on normal power, the fixture is fed from a switch leg and can be turned off by the occupant. The PTS relay coil is fed by unswitched normal power. The normal power from the switch leg is connected to the normally open contacts on the PTS relay.
Electrical
- Dual 120/277 voltage.
- Charge rate/power "ON" LED indicator light and push-to-test switch for mandated code compliance testing.
- 4.8V long life maintenance-free, rechargeable NiCd battery (EM models only).
- Internal solid-state transfer switch automatically connects the internal battery to LED board for minimum 90-minute emergency illumination.
- Fully automatic solid-state, two rate charger initiates battery charging to recharge a discharged battery in 24 hours.
Mounting
- Aluminum mounting canopy included for top or end mount.
- Universal knockout pattern on back plate for wall mount.
Housing
- Premium-grade, die-cast aluminum housing.
- Field selectable knockout Chevron directional indicators.
- Unique design allows double face conversion in the field.
- Quick-snap face plate closure.
Red
Red letters are required for New York City and Chicago approved exit signs.
White
The main housing of these exit signs and emergency lights is painted white or made from a white thermoplastic.
Black
The main housing of these exit signs and emergency lights is painted black or made from a black thermoplastic.
Self-Testing
This feature may be added to many exit sign and emergency light fixtures, the SDT feature prolongs battery life, and reduced man hours required OSHA tests. Self testing diagnostic automatically executes a 15 minute test every 30 days and runs a 90 minutes test once per year. The major reasons batteries typically fail is because they remain dormant for long periods of time. With the SDT feature automatically simulates a full discharge and full recharge to keep the batteries in peak performance. If any problems arise during this testing process it will report them through the user interface. This benefit drastically reduces man hours required by OSHA to manually perform the tests.
Buy America Compliant (BAA)
Products displaying an 'Assembled in the USA' label will contain a percentage of imported components but will be physically assembled in America and are compliant with the Buy American Act (BAA). The FTC states that Assembled in America products must have undergone a significant transformation on American soil.
Specification:
- Faces: Universal
- Letter Color: Red
- Housing Color: White
- Face Color: Black
- Battery Backup: AC Only
- Self Diagnostics: Yes
- Dual-Circuit: 2C-277
- Tamper Proof: No
- Assembled In America: Yes
- Weight: 6 lbs
