- 5 1/4_ wide trim for better covering old holes
- Power 13.5W
- Light colors: 2700K, 3000K, 4000K, 5000K, Dim to Warm 2800-2000K and 3500-2000K
- Superb Light Quality with CRI 90+
- Type IC Rated Ð Approved for Direct Contact with Insulation
- Air-Tight, Wet Location, Insulated and Non Insulated Ceilings
- Triac Dimmable with most CL dimmers 120V Input
- 0-10V Dimmable Option 120V Ð 347V Input
- External Driver Inside Connection Box Ð No Junction Box Needed
- Warranty: 10 Year on Residential, 5 Year on Commercial Installations
- cULus Listed &ÊEnergy Star (except Dim to Warm) certified
Video Overview
Discover this ultimate super thin led recessed fixture
Technical Specifications
CONSTRUCTION:
Round 4_ fixtures with integral LEDs. Isolated external driver factory installed inside junction box.
One driver for every fixture required.
MOUNTING:
Cut Hole In Ceiling And Snap Fixture In Opening With Attached Spring Clips.
2_ Above Ceiling Clearance Required For Driver.
- Default Driver Input Voltage: 120V AC (Dimmable)
- Optional Driver Input Voltage: 277V-347V AC (Not Dimmable)
- Power factor: > 0.98
- Energy Used: 13.5 W
- Halogen equivalent: 75W
- Beam Angle: 110¡
- Light colour options: Warm White 2700K, Soft White 3000K, Neutral White 4000K and Daylight White 5000K
- Dim to Warm options: 3500K to 2000K and 2800K to 2000K
- Light output: Warm White 750 lm, Soft White 760 lm, Neutral White 800 lm and Daylight White 850 lm
- CRI > 90 for True Colour Rendering
- Ambient Operating Temperature: -40¡F (-40¡C) to +104¡F (+40¡C)
- Compliance: cULus Listed
- Rated: Type IC (Direct Contact with Insulation), Energy Star, Air-Tight, T24
DIMENSIONS:
- ID 4 1/8_; OD 5 1/4_; Thickness 1/2_
- Cut out: 4 1/4_ to 4 1/2_
- Junction Box Dimensions (with driver inside): 3 1/2_ x 3 1/2_ x 1 1/2_
Suitable for Wet and Damp locations including showers and soffits.
Installation
ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.
Recessed LED Lights Driver Installation:
CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove one of the half-inch knockouts on the side plate. Install standard L16 cable connector. Use double connector for daisy chaining multiple drivers. Insert line voltage feed into the cable connector and splice same colour wires using wire nuts. Close the cover. Connect the driver to the light fixture Ð the arrows on the male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand. Do not attach the junction box to anything so you can pull it through the ceiling opening in case you need to service the driver in future.
OPTIONS FOR LOCATING DRIVER:
Fixture comes connected to the driver by 12_ long low voltage cable with waterproof connector in the middle.
Depending on where you want the driver to be you have 2 options:
- Locate next to the fixture Ð run line voltage wiring to first junction box and Òdaisy chainÓ to the junction boxes of the other fixtures.
- Or install all drivers at one location and use low voltage extension cables to the fixtures. Use only extensions provided by the manufacturer. Available jumper cables are 6 feet (1.8m) and 20 feet (6m). Cables are linkable.
Maximum run should not exceed 40 feet (12m).
DIMMING:
We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the local voltage and number of fixtures per dimmer.
WARNING:
DO NOT USE ANY OTHER DRIVERS EXCEPT THE LOTUS DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AND THE SIDE PLATES OF THE DRIVER Ð NO SERVICEABLE PARTS INSIDE.
Trim Color Options
Available in White, Brushed Nickel, Brushed Copper and Black Trim
Downloads
CONSTRUCTION:
Round 4_ fixtures with integral LEDs. Isolated external driver factory installed inside junction box.
One driver for every fixture required.
MOUNTING:
Cut Hole In Ceiling And Snap Fixture In Opening With Attached Spring Clips.
2_ Above Ceiling Clearance Required For Driver.
- Default Driver Input Voltage: 120V AC (Dimmable)
- Optional Driver Input Voltage: 277V-347V AC (Not Dimmable)
- Power factor: > 0.98
- Energy Used: 13.5 W
- Halogen equivalent: 75W
- Beam Angle: 110¡
- Light colour options: Warm White 2700K, Soft White 3000K, Neutral White 4000K and Daylight White 5000K
- Dim to Warm options: 3500K to 2000K and 2800K to 2000K
- Light output: Warm White 750 lm, Soft White 760 lm, Neutral White 800 lm and Daylight White 850 lm
- CRI > 90 for True Colour Rendering
- Ambient Operating Temperature: -40¡F (-40¡C) to +104¡F (+40¡C)
- Compliance: cULus Listed
- Rated: Type IC (Direct Contact with Insulation), Energy Star, Air-Tight, T24
DIMENSIONS:
- ID 4 1/8_; OD 5 1/4_; Thickness 1/2_
- Cut out: 4 1/4_ to 4 1/2_
- Junction Box Dimensions (with driver inside): 3 1/2_ x 3 1/2_ x 1 1/2_
Suitable for Wet and Damp locations including showers and soffits.
Discover this ultimate super thin led recessed fixture
Specification Sheets
Line Voltage model: LL4R
24V DC model: LL4R24V
Sell Sheet
LL4R
pdf files
LL4R-27K | LL4R-30K | LL4R-40K | LL4R-50K
IES files
LL4R-27K | LL4R-30K | LL4R-40K | LL4R-50K
Links to Energy Star: LL4R-27K | LL4R-30K | LL4R-40K | LL4R-50K
ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.
Recessed LED Lights Driver Installation:
CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove one of the half-inch knockouts on the side plate. Install standard L16 cable connector. Use double connector for daisy chaining multiple drivers. Insert line voltage feed into the cable connector and splice same colour wires using wire nuts. Close the cover. Connect the driver to the light fixture Ð the arrows on the male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand. Do not attach the junction box to anything so you can pull it through the ceiling opening in case you need to service the driver in future.
OPTIONS FOR LOCATING DRIVER:
Fixture comes connected to the driver by 12_ long low voltage cable with waterproof connector in the middle.
Depending on where you want the driver to be you have 2 options:
- Locate next to the fixture Ð run line voltage wiring to first junction box and Òdaisy chainÓ to the junction boxes of the other fixtures.
- Or install all drivers at one location and use low voltage extension cables to the fixtures. Use only extensions provided by the manufacturer. Available jumper cables are 6 feet (1.8m) and 20 feet (6m). Cables are linkable.
Maximum run should not exceed 40 feet (12m).
DIMMING:
We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the local voltage and number of fixtures per dimmer.
WARNING:
DO NOT USE ANY OTHER DRIVERS EXCEPT THE LOTUS DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AND THE SIDE PLATES OF THE DRIVER Ð NO SERVICEABLE PARTS INSIDE.
