Larson Electronics 80W Solar Powered LED Light w/ 265W Panel - (4) 250 aH 12V Batteries - Pole Mount Panel - 40' Cord

Made in the USA The Larson Electronics SPLEDXL-P10W80X2ET-4X250AH Solar Powered LED Light is an ideal lighting solution for remote areas and standalone applications where connection to external power is either impractical or unavailable. This rechargeable solar powered LED light is offered in a spotlight or floodlight beam pattern and several different operating configurations, making it ideal for remote applications. For robust illumination, the unit uses a high intensity LED lamp, capable of producing 6,880 lumens of white light. This solar powered LED light is offered in several different configurations and powered by four, 250aH sealed lead acid 12V batteries that are recharged by a 265 watt solar panel. Light output comes from one, 80-watt LED lamp producing 6,880 lumens during use. This solar-powered lighting system is configured to operate non-stop 24/7, day/night with photocell, motion sensor for security purposes, on/off switch for manual operation or flying leads for operators to connect to user provided external switches. The day/night and motion sensor is programmed to activate the solar panel in the evening and to shut it off during the day, activating the LED light when ambient lighting falls below 1 lux. The motion sensor will activate the panel upon detecting movement within range of the panel. The sealed lead acid battery pack is contained within the solar panel, not the light. Charging time for the battery is 5 hours when exposed to direct sunlight. As with all solar powered equipment, charging time is affected by the amount of available ambient light. When ambient light levels drop below a certain level, such as on cloudy days, the unit will not recharge. Mounting options include the ability to attach the fixture to flat surfaces such as walls or round/square pole mounting such as on flagpoles or structure supports. Light Features: The solar powered system is equipped with one high intensity LED light, which produces 6,880 lumens of bright light while drawing only 80 watts @ 6.7 amps from a 12 volt electrical system. Eight CREE XLamp MC-E¨ ten watt LEDs producing 860 lumens each are arranged in two rows and paired with high purity optics to produce a 20 degree spread spot beam approximately 750’ long by 75’ in width. We also offer floodlight versions with a 40 degree beam spread to provide more light over a larger area nearer the fixture, making flood versions ideal for use as work lights. These LED light bars are waterproof to 3 meters, sealed against intrusion by dust and dirt and very ruggedly constructed to withstand the most demanding environments, conditions and applications. PWM Control: The pulse width modulation drivers in this unit also provide secondary benefits through the ability to tap into a provided input wire with an external pulse generator and adjust the duty cycle of the current being applied to the LEDs. Thus you can connect an external dimmer, switch or pulse control and adjust the perceived output of the light, effectively causing the light to flash, dim or brighten to the desired levels. Additionally, this method of controlling light output results in a corresponding drop in amperage draw, so if the duty cycle is cut back to 50% there will be a matching 50% reduction in amperage draw. These units are also able to monitor and adjust input current to maintain the correct LED voltage levels regardless of input levels across a specific range. These LEDP10W series light bars can operate on current ranging from 9 to 46VDC without any modifications necessary as a result. This ability to sense and adjust input current also provides protection against voltage spikes and drops that can occur in vehicle electrical systems which would otherwise result in burning up or premature LED failure without it. LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation and/or transportation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool down time before re-striking. Because there is no warm up period, this light can be cycled on and off with no reduction in lamp life. LED lights run at significantly cooler temperatures than traditional metal halide and high pressure sodium lights and contain no harmful gases, vapors, or mercury, making them both safer and more energy efficient. No extra energy is wasted in cooling enclosed work areas due to external heat emissions from bulb type lights, and the operator risks associated with traditional lighting methods, such as accidental burns and exposure to hazardous substances contained in the glass bulbs, are eliminated. In addition, LEDs are also safer for the environment as they are 100% recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps. Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units contain advanced drivers which use pulse width modulation to control heat buildup rather than simple voltage regulators which are typically harsh on sensitive electronics and can contribute to early LED failure. These units automatically sense the temperature of each LED and adjust the energy frequency or "duty cycle" accordingly to maintain heat levels within acceptable ranges. This system in essence flashes current at an extremely fast on and off rate to each LED based upon the LED`s core temperature. This flash rate is too fast to detect with the human eye, but provides precise control of the current flowing to each LED and thus the heat it generates. This allows the LEDs to be driven at up to 100% capacity without overheating or visible loss of light output. The LEDs are always driven at the same voltage but the duty cycle, however, is changed to alter how long the LEDs are actually on or off. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 50,000 hours. Durability: As well as unparalleled heat control, the LEDP10W series of LED light bars from Larson Electronics also offer IP68 rated construction that is designed to withstand extremes of environmental and operating conditions. These units can withstand rapid temperature changes of -40 degrees Celsius to 85 degrees Celsius, are waterproof to three meters and resist ingress of dust, dirt and humidity. The housings are formed from extruded aluminum and the lenses are unbreakable polycarbonate. The CREE XLamp MC-E¨ LEDs offer resistance to shocks and vibrations and are rated at 70% lumen maintenance after 50,0000 hours of use. Wiring: The SPLEDXL-P10W80X2ET-4X250AH comes with a 20-foot cord connecting the solar panel and the batteries and another 20-foot cord connecting the light and the batteries. This allows the light to be mounted separately from the panel. This means the solar panel can be mounted in direct sunlight while the light is mounted in a workspace. The cord between the light and panel ends in Deutsch connectors, allowing an optional longer extension cord to be attached, increasing the distance the light can be installed from the panel. Optional longer extension cords are available at additional cost. Alternatively, the light can be mounted directly to the panel. Larson Electronics can also configure this light for special requirements including different lights and larger batteries. Applications: Suggested uses for this light include both commercial and industrial applications as well as consumer based installations. This light is ideal for boat docks, remote locations that rely on batteries for power, exterior outbuilding lighting, hunting cabins, parking areas, sign or entryway illumination, driveway lighting and anywhere a standalone lighting solution is needed. At Larson Electronics, we do more than meet your lighting needs. We also provide replacement, retrofit, and upgrade parts as well as industrial grade power accessories. Our craftsmen can custom build any lighting system and/or accessories to fit the unique demands of your operation. A commitment to honesty, quality, and dependability has made Larson Electronics a leader in the lighting and electronics business since 1973. Contact us today at 800-369-6671 or message [email protected] for more information about our custom options tailored to meet your specific industry needs. Specifications / Additional Information SPLEDXL-P10W80X2ET-4X250AH Solar Powered LED Light Features/Quick Summary Unit Type: Solar Powered LED Light CREE XLamp MC-E¨ LED Panel Dimensions: 65.43"L x 38.98"W x 1.81"H 100% Solar - Requires no External Power Lamp Dimensions: 8" x 4" x 3.5" Fast Average Current Control Panel Wattage: 265W Programmable Off-time Switching Light Watts: 80W Linear Dimming Iutput Lumens: 6,880 PWM Dimming Input LED Lamp Life: 50,000+ Hours Short Protection w/Skip Mode Lamp Configuration: 20¡ Spot or 40¡ Flood LED Color Temperature: 6000K Flood Beam: Lux @ 1 meter = 17,500; @ 3 meters = 1,900 Spot Beam: Lux @ 1 meter = 31,000; @ 3 meters = 4,000 LED Drive/Optics Efficiency: 90% Amps: 6.7 @ 12V Panel Mounting: Surface or Pole Lamp Mounting: Flat Surface or Tube - Adjustable Special Orders-Special Requirements Battery: (4) 250aH sealed lead acid batteries Contact us for special requirements Charging Time: 5 Hours Phone: 1-214-616-6180 Wiring: 40` 16/2 SOOW Cable w/ Deutsch 2-pin Disconnect (20` Between Panel and Batteries, 20` Between Light and Batteries) Toll Free: 1-800-369-6671 Light Housing Color: Black or White E-mail: [email protected] Down to Purchase-